 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| vol . 1 2 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e
for correct use of super capacitors 1.please confirm the operating conditions and the specifications of the super capacitors befor using them. 2. the electrolyte of these super capacitors is sealed with material such as rubber. when you use the capacitors for a long time at high temperature, the moisture of the eleotrolyte evaporates and the equivalent series resistance (e.s.r.) increases. the fundamental failure mode is the open mode depending on e.s.r. increase. when using a capacitor, please introduce a safe design assuming unex- pected capacitor failure, such as redundancy in design and protection from fire and erroneous operation. 3. please read 'notes on using the super capacitor' on page 60 when you design the circuits using the super capacitors. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 1. organization of super capacitor series ??????????????????????? 4 2. performance for selection ????????????????????????????? 5 3. characteristics of super capacitor ????????????????????????? 5 4. typical applications ???????????????????????????????? 6 5. part number system ???????????????????????????????? 7 6. rated specifications ???????????????????????????????? 9 6.1 fc series smd type ???????????????????????????? 9 6.2 fm series ?????????????????????????????????? 13 6.3 fg series ?????????????????????????????????? 20 6.4 ft series ?????????????????????????????????? 22 6.5 fy series ?????????????????????????????????? 24 6.6 fr series ?????????????????????????????????? 26 6.7 fs series ?????????????????????????????????? 28 6.8 fa | fe series ???????????????????????????????? 30 6.9 hv series high capacitance type ?????????????????????? 32 7. packing ?????????????????????????????????????? 33 8. list of plating type and sleeve type ???????????????????????? 34 9. measurement conditions ?????????????????????????????? 35 10. notes on using super capacitor electric double-layer capacitor ????????? 36 contents page all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 4 super capacitors vol.12 1. organization of super capacitor series for automatic mounting smd embossad taping 25 to 70? guaranteed ma order back-up a order back-up 40 to 85? guaranteed for automatic mounting radial taping can case type self-supporting type fc series 3.5 to 5.5v fm series 3.5 to 6.5v fg series 3.5 to 5.5v fy series 3.5 to 5.5v fr series 5.5v fs series 5.5 to 11v fe series 5.5v fa series 5.5 to 11v hv series 2.7v 10 to 100f ft series 5.5v fgr type 5.5v fme fml type 5.5v fmr type 3.5 to 5.5v 40 to 85? guaranteed for a order current all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 5 2. performance for selection 3. characteristics of super capacitor super capacitor can not be used for applications in ac circuit such as ripple absorption because it has high internal resistanc e (several hundred m to a hundred ) compared to aluminum electrolysis capacitor. thus its main use would be similar to that of secondary battery such as power back-up in dc circuit. the following list shows the characteristics of super capacitors as compared to aluminum electrolyses capacitors for power back-up and secondary batteries. secondary battery capacitor nicd battery lithium ion battery aluminum electrolysis capacito super capacitor back-up ability ?? eco-hazard cd operating temperature range 20 to 60 ? 20 to 50 ? 55 to 105 ? 40 to 85 ?fr|ft charge time few hours few hours few minutes few minutes charge/discharge life time approx. 500 times approx. 500 to 1000 times limitless (*1) limitless (*1) restrictions on charge/discharge yes yes none none flow soldering not applicable not applicable applicable applicable automatic mounting not applicable not applicable applicable applicable (fm and fc series) safety risks leakage, explosion leakage, combustion, explosion, ignition heat-up, explosion gas emission (*2) (*1) aluminum electrolysis capacitor and super capacitor has limited lifetime. however, when used under proper conditions, both can operate suf ciently within the designed lifetime of the set they are built in. (*2) there is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid). however, application of abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion. backup time depends on capacitance 1 minute backup time backup current depends on supercapacitor equivalent series resistance (esr) high esr backup current low esr 0.01 0.1 1 10 10 2 10 3 10 4 10 5 10 6 10 7 10 8 ka a ma a 1 hour 1 day 1 week 1 month ( sec ) high power supercapacitor box type low impedance application use fa, fe, fs, ft, fm series high impedance application use fg, fy, fc, fm, fr series high power supercapacitor hv series all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 6 super capacitors vol.12 4. typical applications as in the characteristics remarked previously, super capacitor has characteristics intermediate between general capacitors and batteries. because of this, super capacitor can be used like a secondary battery when applied to dc circuit. the best suited applications of super capacitor are back-up device for the power shut-down of micro computers and ram's. the list below shows main application examples. application examples of super capacitor intended use (guideline) power supply (guideline) application examples of equipments series long time back-up 500 a and below ~ cmos ram, ic for clocks ~ measuring device, control equipment, communication device, automotive power source ~fr series (85 ? guaranteed) ~ cmos micro computer, ic for clocks ~ cmos micro computer ~ static ram/dts (digital tuning system) ~fc series ~fg series ~ fy series ~fm series back-up for 1 hour or less 50 ma and below ~ micro computer, ram ~ vcr, microwave oven, ~ micro computer ~ memory equipped device ~ ft series ~fs series ~ driving motor ~ vcr, printer, projector ~ video disk ~ subsidiary power supply for driving motor during voltage drop ~ camera back-up for 10 seconds or less 1 a and below ~ power source of toys, led, buzzer ~ toys, display device, alarm device ~ fa series ~fe series ~ high current supply for a short amount of time ~ actuator, relay solenoid, gas igniter power assist up to several a ~ power supply, subsidiary power supply ~ street sign, display light , ups ~hv series all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 7 5. part number system fg series bulk type fg 0h 223 z f environmental pollutant reduced capacitance tolerance 80?, 20? nominal capacitance f first two digits represent significant figure third digit specifies number of zeroes to follow microfarad code. maximum operating voltage 0v3.5vdc, 0h5.5vdc, 0j6.5vdc, 1a11vdc, 1b12vdc series name height (excluding lead) 1616mm 1818mm tape type bulk part name fm series tape type (ammo pack) fm0h223zf tp 16 fc series tape type (embossed tape) fc0h104zf tb r 24 - ss indivisual management code tape width positive electrode position in relation to tapes forward direction embossed tape type bulk part name fm, fc, ft, fg, fs, fr, fy, fe, fa series all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 8 super capacitors vol.12 hv series hv 0e 106 n f environmental pollutant reduced capacitance tolerance ?30? nominal capacitancef first two digits represent significant fifure third digit specifies number of zeroes to follow microfarad code. maximum operating voltage 0e2.7vdc series name all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 9 markings displays nominal capacitance, max operating voltage serial number, polarity and etc. standard models /? fc type part number max. operating voltage (vdc) nominal capacitance discharge system (f) max. esr (at 1khz) ( ) max. current at 30 minutes (ma) voltage holding characteristic min. (v) dimension (unit:mm) weight (g) dhab i wp k l fc0h473zftbr24 5.5 0.047 50 0.071 4.2 10.5 5.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.0 0.1 fc0h104zftbr24 5.5 0.10 25 0.15 4.2 10.5 5.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.0 0.1 fc0h224zftbr24 5.5 0.22 25 0.33 4.2 10.5 8.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.4 0.1 fc0h474zftbr32-ss 5.5 0.47 13 0.71 4.2 16.0 9.5 16.3 16.3 6.8 ? 1.0 1.2 5.0 1.2? 0.5 0 0.5 4.0 0.1 fc0h105zftbr44-ss 5.5 1.0 7 1.50 4.2 21.0 10.5 21.6 21.6 7.0 ? 1.0 1.4 10.0 1.2? 0.5 0 0.5 6.7 0.1 fc0v104zftbr24 3.5 0.10 50 0.09 ? 10.5 5.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.0 0.1 fc0v224zftbr24 3.5 0.22 25 0.20 ? 10.5 5.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.0 0.1 fc0v474zftbr24 3.5 0.47 25 0.42 ? 10.5 8.5 10.8 10.8 3.6 ? 0.5 1.2 5.0 0.7? 0.3 0 0.3 1.4 0.1 /? fch type part number max. operating voltage (vdc) nominal capacitance discharge system (f) max. esr (at 1khz) ( ) max. current at 30 minutes (ma) voltage holding characteristic min. (v) dimension (unit:mm) weight (g) dhab i wp k l fch0v683zftbr16 3.6 0.068 40 0.062 ? 6.8 3.7 6.8 6.8 2.9 ? 0.5 0.7 2.5 0.7? 0.3 0 0.3 0.3 0.1 fch0h433zftbr16 5.5 0.043 50 0.065 ? 6.8 5.0 6.8 6.8 2.9 ? 0.5 0.7 2.5 0.7? 0.3 0 0.3 0.4 0.1 /? fcs type part number max. operating voltage (vdc) nominal capacitance discharge system (f) max. esr (at 1khz) ( ) max. current at 30 minutes (ma) voltage holding characteristic min. (v) dimension (unit:mm) weight (g) dhab i wp k l fcs0h473zftbr24 5.5 0.047 100 0.071 4.2 10.7 5.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.0 0.1 fcs0h104zftbr24 5.5 0.10 50 0.15 4.2 10.7 5.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.0 0.1 fcs0h224zftbr24 5.5 0.22 50 0.33 4.2 10.7 8.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.4 0.1 fcs0v104zftbr24 3.5 0.10 100 0.09 ? 10.7 5.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.0 0.1 fcs0v224zftbr24 3.5 0.22 50 0.20 ? 10.7 5.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.0 0.1 fcs0v474zftbr24 3.5 0.47 50 0.42 ? 10.7 8.5 10.8 10.8 3.9 ? 0.5 1.2 5.0 0.9? 0.3 0 0.3 1.4 0.1 d?0.5 b?0.2 a?0.2 negative terminal positive terminal w?0.1 h max. l k ii p 473 5.5v a1 nominal capacitance max operating voltage date code polarity (negative) fc 5.5v 474 a1-001 nominal capacitance max operating voltage serial number polarity (negative) series name logo n t date code fc0h473zftbr24 fc0h104zftbr24 fc0h224zftbr24 fc0v104zftbr24 fc0v224zftbr24 fc0v474zftbr24 fch0v683zftbr16 fch0v433zftbr16 473 5.5v a1 s nominal capacitance max operating voltage date code fcs type polarity (negative) fcs0h473zftbr24 fcs0h104zftbr24 fcs0h224zftbr24 fcs0v104zftbr24 fcs0v224zftbr24 fcs0v474zftbr24 fc0h474zftbr32-ss fc0h105zftbr44-ss 6. rated speci cations 6.1 fc series features ? enables surface mounting. ? high rated voltage of 5.5v. ? high leakage reliability. dimensions all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 10 super capacitors vol.12 ~ fc, fch type temperature on the capacitor top ( ?) 250 200 150 100 50 0 time (sec) tp time exceeding 200 ? 120 sec 160 ? reflow profile peak temperature peak temperature : 235?| within 10sec. peak temperature ( ?) 250 240 230 220 210 200 tp (sec) tp time exceeding 200? 0 10 20 30 40 50 60 reflow profile 0 50 100 150 200 250 300 0 50 100 150 200 250 300 350 400 time (sec) temperature ( ? ) 200 ? 150? 260? temperature on the capacitor top 217? 70sec 150sec ~ fcs type ~ above "reflow profile" graph indicates temperature at the terminals and capacitor top. ~ above "reflow profile" graph indicates temperature at the terminals and capacitor top. precautions for use ~ this series is exclusively for re ow soldering. it is designed for thermal conduction system such as combination use of infrar ed ray and heat blow. consult with nec tokin before applying other methods. ~ the re ow condition must be kept within re ow pro le graphs shown below. ~ applying re ow soldering is limited to 2 times. after the rst re ow, cool down the capacitor thoroughly to 5-35 ? before the second re ow. always consult with nec tokin when applying re ow soldering in a more severe condition than the condition described here. peak temperature below 260 ? over 255 ? within 10sec. over 230 ? within 45sec. over 220 ? within 60sec. over 217 ? within 70sec. time between 150 ? to 200 ? temperature zone over 170 ?1 within 50sec. 150sec. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 11 tape and reel dimensions [reel dimensions] dimensions of indented [square-hole plastic tape] /?tbr16/24 t 1 t 2 super capacitors fitting on square-hole super capacitors fitting on square-hole t 1 t 2 a b p 1 p 2 p 0 f e w forward direction sprocket hole indented square-hole for fitting super capacitors a b g p 1 r0.75 0.2 p 2 p 0 f e w f d 0 f d 0 b w a c e d r:10 t /?tbr32/44 bab c logo recommended land pattern land pattern lead terminal (mm) part number a b c fc0h473zftbr24 5.0 4.6 2.5 fc0h104zftbr24 5.0 4.6 2.5 fc0h224zftbr24 5.0 4.6 2.5 fc0h474zftbr32-ss 5.0 10.0 2.5 fc0h105zftbr44-ss 10.0 10.5 3.5 fc0v104zftbr24 5.0 4.6 2.5 fc0v224zftbr24 5.0 4.6 2.5 fc0v474zftbr24 5.0 4.6 2.5 fch0v683zftbr16 2.5 4.0 1.4 fch0h433zftbr16 2.5 4.0 1.4 fcs0h473zftbr24 5.0 4.9 2.5 fcs0h104zftbr24 5.0 4.9 2.5 fcs0h224zftbr24 5.0 4.9 2.5 fcs0v104zftbr24 5.0 4.9 2.5 fcs0v224zftbr24 5.0 4.9 2.5 fcs0v474zftbr24 5.0 4.9 2.5 (mm) part number a b c fc0h473zftbr24 5.0 3.6 1.2 fc0h104zftbr24 5.0 3.6 1.2 fc0h224zftbr24 5.0 3.6 1.2 fc0h474zftbr32-ss 5.0 6.8 1.2 fc0h105zftbr44-ss 10.0 7.0 1.4 fc0v104zftbr24 5.0 3.6 1.2 fc0v224zftbr24 5.0 3.6 1.2 fc0v474zftbr24 5.0 3.6 1.2 fch0v683zftbr16 2.5 2.9 0.7 fch0h433zftbr16 2.5 2.9 0.7 fcs0h473zftbr24 5.0 3.9 1.2 fcs0h104zftbr24 5.0 3.9 1.2 fcs0h224zftbr24 5.0 3.9 1.2 fcs0v104zftbr24 5.0 3.9 1.2 fcs0v224zftbr24 5.0 3.9 1.2 fcs0v474zftbr24 5.0 3.9 1.2 (mm) mark tbr16 tbr24 tbr32 tbr44 a 380 ?2 380?2 330? 2 380?2 b80 ?1 product height 5.5mm 80?1 100? 1 100?1 product height 8.5mm 100?1 c13 ?0.5 13?0.5 13? 0.5 13?0.5 d21 ?0.8 21?0.8 21? 0.8 21?0.8 e2 ?0.5 2?0.5 2? 0.5 2?0.5 w 17.5 ?1.0 product height 5.5mm 25.5?0.5 33.5? 1.0 45.5?1.0 product height 8.5mm 25.5?1.0 t 2.0 2.0 2.0 2.0 (mm) mark tbr16 tbr24 tbr32 tbr44 w 16.0 24.0 32.0 44.0 a 7.2 11.4 18.0 23.0 b 9.0 13.0 20.0 25.0 p 0 4.0 4.0 4.0 4.0 p 1 12.0 16.0 24.0 32.0 p 2 2.0 2.0 2.0 2.0 f 7.5 11.5 14.2 20.2 d 0 1.55 1.55 1.55 1.55 t 1 0.4 0.4 0.5 0.5 e 1.75 1.75 1.75 1.75 t 2 5.0 product height 5.5mm 6.0 10.0 12.0 product height 8.5mm 8.4 g 28.4 40.4 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 12 super capacitors vol.12 speci cations series name item fc test conditions (conforming to jis c 5160-1) 5.5v type, 3.5v type category temperature range 25 ? to 70 ? max operating voltage 5.5vdc, 3.5vdc capacitance refer to standard ratings refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z * surge capacitance more than 90% of initial ratings surge voltage 4.0v (3.5v type, 3.6v type) 6.3v (5.5v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.043f, 0.047f 300 0.068f 240 0.10f 150 0.22f 56 0.47f 30 1.0f 15 discharge resistance0 temperature 70?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality * characteristics in different temperature capacitance phase 2 50% higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value capacitance phase 3 esr capacitance phase 5 200% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings * vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency 10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality * solder heat resistance capacitance satisfy initial ratings cooled down to ambient temperature after re ow soldering, then the product must ful ll the condition stated left. (see page 10 for re ow condition) esr current (30 minutes value) appearance no obvious abnormality * temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 25 ? room temperature 70 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality * high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality * high temperature load capacitance within ?30% of initial value conforms to 4.15 voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality * self discharge characteristics (voltage holding characteristics) 5.5v type: voltage between terminal leads higher than 4.2v 3.5v type: not speci ed charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humidity lower than 70%rh as for items with l* z , it must ful ll the above condition after the re ow soldering. (see page 10 for re ow conditions) all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 13 dimensions 5.5v 473 a1 e + C nominal capacitance e fme type marking l fml type marking r fmr type marking negative polarity identification date code polarity max operating voltage 11.5?0.5 5?1 0.4?0.1 0.5?0.1 0.4?0.1 10.5?0.5 5?0.5 t?0.5 n t unitmm 6.2 fm series !12.2 to 5mm lead length designation for transverse mounting ?l1? lead terminal forming example markings all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 14 super capacitors vol.12 speci cations /? 5.5v type part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v t mm weight g bulk ammo pack charge system(f) discharge system(f) fm0h103zf fm0h103zftp 5.5 0.01 0.014 300 0.015 4.2 5.0 1.3 fm0h223zf fm0h223zftp 5.5 0.022 0.028 200 0.033 4.2 5.0 1.3 fm0h473zf fm0h473zftp 5.5 0.047 0.06 200 0.071 4.2 5.0 1.3 fm0h104zf fm0h104zftp 5.5 0.10 0.13 100 0.15 4.2 6.5 1.6 fm0h224zf fm0h224zftp 5.5 0.22 100 0.33 4.2 6.5 1.6 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" /? 3.5v type part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma t mm weight g bulk ammo pack charge system(f) discharge system(f) fm0v473zf fm0v473zftp 3.5 0.047 0.06 200 0.042 5.0 1.3 fm0v104zf fm0v104zftp 3.5 0.10 0.13 100 0.090 5.0 1.3 fm0v224zf fm0v224zftp 3.5 0.22 0.30 100 0.20 6.5 1.6 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" /? 6.5v type part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma t mm weight g bulk ammo pack charge system(f) discharge system(f) fm0j473zf fm0j473zftp 6.5 0.047 0.062 200 0.071 6.5 1.6 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" /? fme, fml type (buckup large current, ma order) part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma t mm weight g bulk ammo pack charge system(f) discharge system(f) fme0h223zf fme0h223zftp 5.5 0.022 0.028 40 0.033 5.0 1.3 fme0h473zf fme0h473zftp 5.5 0.047 0.06 20 0.071 5.0 1.3 fml0h333zf fml0h333zftp 5.5 0.033 6.5 0.050 5.0 1.3 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" /? fmr type (max operating temperature 85 ? type) part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v t mm weight g bulk ammo pack charge system(f) discharge system(f) fmr0h473zf fmr0h473zftp 5.5 0.047 0.062 200 0.071 4.2 6.5 1.6 fmr0h104zf fmr0h104zftp 5.5 0.10 50 0.15 4.2 6.5 1.6 fmr0v104zf fmr0v104zftp 3.5 0.10 50 0.090 6.5 1.6 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 15 /? fmc type chip parts applicable to treatment in bond hardening furnace (160?5 ? for 120?10 seonds) 5.5v 473 k1 c + C nominal capacitance cfmc type marking negative polarity identification date code polarity max operating voltage a ?0.5 5?1 0.4?0.1 d 1 ?0.1 d 2 ?0.1 b ?0.5 5?0.5 t?0.5 n t unitmm dimensions markings speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v a (mm) b (mm) t (mm) d 1 (mm) d 2 (mm) weight g bulk ammo pack charge system(f) discharge system(f) fmc0h473zf fmc0h473zftp 5.5 0.047 0.06 100 0.071 4.2 11.5 10.5 5.0 0.5 0.4 1.3 fmc0h104zf fmc0h104zftp 5.5 0.10 0.13 50 0.15 4.2 11.5 10.5 6.5 0.5 0.4 1.6 fmc0h334zf fmc0h334zftp 5.5 ? 0.33 25 0.50 4.2 15.0 14.0 9.0 0.6 0.6 3.5 to complete the part number, insert lead length (16mm or 18mm) in to the "( )" all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 16 super capacitors vol.12 taping speci cation [except fmc0h334zftp( )] p 2 a l w 2 w 0 w 1 w p 1 p 0 d 0 w 4 t 3 t 1 t 2 f h c h b p ? unitmm item symbol value tolerance remarks component height a 11.5 ?0.5 component width b 10.5 ?0.5 component thickness c ? 0.5 5.5 v type : 5.0/0.010f to 0.047f, 6.5/0.047f 3.5 v type : 5.0/0.047f to 0.10f, 6.5/0.22f fme type : 5.0/0.022f to 0.047f fml type : 5.0/0.033f 6.5 v type : 6.5/0.047f, 0.10f fmr type : 6.5/0.047f fmc type : 5.0/0.047f, 6.5/0.10f lead-wire width w 4 0.5 ?0.1 lead-wire thickness t 3 0.4 ?0.1 pitch between component p 12.7 ?1.0 sprocket hole pitch p 0 12.7 ?0.3 sprocket hole to lead p 1 3.85 ?0.7 ? p 2 6.35 ?1.3 lead spacing f 5.0 ?0.5 component alignment ? h 2.0 max. including tilting caused by bending lead wire. tape width w 18.0 1.0 0.5 hold-down tape width w 0 12.5 min. sprocket hole position w 1 9.0 ?0.5 hold-down tape position w 2 3.0 max. no protrusion of tape. component's bottom line position h 16.0 ?0.5 ? 18.0 ?0.5 sprocket hole diameter d 0 4.0 ?0.2 total tape thickness t 1 0.7 ?0.2 ? t 2 1.5 max. defect component cut-off position l 11.0 max. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 17 taping speci cation [except fmc0h334zftp ( )] p 2 l w 2 w 0 w 1 w p 0 d 0 w 4 t 3 t 1 t 2 h c b p p 1 f a h ? unitmm item symbol value tolerance remarks component height a 15.0 ?0.5 component width b 14.0 ?0.5 component thickness c 9.0 ?0.5 lead-wire width w 4 0.6 ?0.1 lead-wire thickness t 3 0.6 ?0.1 pitch between component p 25.4 ?1.0 sprocket hole pitch p 0 12.7 ?0.3 sprocket hole to lead p 1 3.85 ?0.7 ? p 2 6.35 ?1.3 lead spacing f 5.0 ?0.5 component alignment ? h 2.0 max. including tilting caused by bending lead wire tape width w 18.0 1.0 0.5 hold-down tape width w 0 12.5 min. sprocket hole position w 1 9.0 ?0.5 hold-down tape position w 2 3.0 max. no protrusion of tape component's bottom line position h 16.0 ?0.5 ? 18.0 ?0.5 sprocket hole diameter d 0 4.0 ?0.2 total tape thickness t 1 0.67 ?0.2 ? t 2 1.7 max. defect component cut-off position l 11.0 max. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 18 super capacitors vol.12 speci cations series name item 5.5v type, 3.5v type, 6.5v type fmc type fml, fme type test conditions (conforming to jis c 5160-1) category temperature range 25 ? to 70 ? 25 ? to 70 ? max operating voltage 5.5vdc, 3.5vdc, 6.5vdc 5.5vdc capacitance 5.5v0.010f to 0.33f 3.5v0.047f to 0.22f 6.5v0.047 0.022f, 0.033f, 0.047f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings refer to standard ratings measured at 1khz, 10ma ; see also lmeasurement conditions z current (30-minutes value) refer to standard ratings refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings more than 90% of initial ratings surge voltage 4.0v (3.5v type) 6.3v (5.5v type) 7.4v (6.5v type) charge30 sec. discharge9min 30sec. number of cycles 1000 series resistance 0.010f 1500 0.022f 560 0.033f 510 0.047f 300 0.068f 240 0.10f 150 0.22f 56 0.33f 51 discharge resistance0 t emperature70? 2 ? esr not to exceed 120% of initial ratings not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings not to exceed 120% of initial ratings appearance no obvious abnormality no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value phase 2 50% or higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value 400% or less than initial value capacitance phase 3 phase 3 esr capacitance phase 5 200% or less than initial value phase 5 200% or less than initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value phase 6 within ?20% of initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) satisfy initial ratings satisfy initial ratings lead strength (tensile) no terminal damage no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.13 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality temperature cycle capacitance satisfy initial ratings satisfy initial ratings conforms to 4.12 temperature condition 25 ? room temperature 70 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality high temp. and high humidity resistance capacitance within ? 20% of initial value within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings not to exceed 120% of initial ratings appearance no obvious abnormality no obvious abnormality high temperature load capacitance within ? 30% of initial value within ?30% of initial value conforms to 4.15 temperature 70?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings below 200% of initial ratings current (30 minutes value) below 200% of initial ratings below 200% of initial ratings appearance no obvious abnormality no obvious abnormality self discharge characteristics (voltage holding characteristics) 5.5v type: voltage between terminal leads higher than 4.2v 3.5v type: not speci? ed 6.5v type: not speci? ed charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humiditylower than 70%rh all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 19 speci cations series name item fmr type test conditions (conforming to jis c 5160-1) category temperature range 40 ? to 85 ? max operating voltage 5.5vdc, 3.5vdc capacitance 0.047f, 0.10f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 4.0v (3.5v type) 6.3v (5.5v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.047f 300 0.10f 150 discharge resistance0 temperature 85?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase340?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value capacitance phase 3 30% or higher than initial value esr below 700% of the initial value capacitance phase 5 200% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency 10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 40 ? room temperature 85 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance within ?30% of initial value conforms to 4.15 temperature 85?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality self discharge characteristics (voltage holding characteristics) 5.5v type: voltage between terminal leads higher than 4.2v 3.5v type: not speci? ed charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humidity lower than 70%rh all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 20 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. ymin. f d 2 ? 0.1 terminal a1 001 a1 fg fg 5.5 v 5.5 v 0.22 f 0.22 f negative polarity identification mark super capacitor max operating voltage nominal capacitance date code serial number 6.3 fg series dimensions markings on sleeve /? fg type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fg0h103zf 5.5 0.010 0.013 300 0.015 4.2 11.0 5.5 5.08 2.7 0.2 1.2 0.9 fg0h223zf 5.5 0.022 0.028 200 0.033 4.2 11.0 5.5 5.08 2.7 0.2 1.2 1.0 fg0h473zf 5.5 0.047 0.060 200 0.071 4.2 11.0 5.5 5.08 2.7 0.2 1.2 1.0 fg0h104zf 5.5 0.10 0.13 100 0.15 4.2 11.0 6.5 5.08 2.7 0.2 1.2 1.3 fg0h224zf 5.5 0.22 0.28 100 0.33 4.2 13.0 9.0 5.08 2.2 0.4 1.2 2.5 fg0h474zf 5.5 0.47 0.60 120 0.71 4.2 14.5 18.0 5.08 2.4 0.4 1.2 5.1 fg0h105zf 5.5 1.0 1.3 65 1.5 4.2 16.5 19.0 5.08 2.7 0.4 1.2 7.0 fg0h225zf 5.5 2.2 2.8 35 3.3 4.2 21.5 19.0 7.62 3.0 0.6 1.2 12.1 fg0h475zf 5.5 4.7 6.0 35 7.1 4.2 28.5 22.0 10.16 6.1 0.6 1.4 27.3 fg0v155zf 3.5 1.5 2.2 65 1.5 16.5 14.0 5.08 3.1 0.4 1.2 5.2 /? fgh type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fgh0h104zf 5.5 0.10 100 0.15 4.2 11.0 5.5 5.08 2.7 0.2 1.2 1.0 fgh0h224zf 5.5 0.22 100 0.33 4.2 11.0 7.0 5.08 2.7 0.2 1.2 1.3 fgh0h474zf 5.5 0.47 65 0.71 4.2 16.5 8.0 5.08 2.7 0.4 1.2 4.1 fgh0h105zf 5.5 1.0 35 1.5 4.2 21.5 9.5 7.62 3.0 0.6 1.2 7.2 /? fgr type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fgr0h474zf 5.5 0.47 0.60 120 0.71 4.2 14.5 18.0 5.08 2.4 0.4 1.2 5.1 fgr0h105zf 5.5 1.0 1.3 65 1.5 4.2 16.5 19.0 5.08 2.7 0.4 1.2 7.0 fgr0h225zf 5.5 2.2 2.8 35 3.3 4.2 21.5 19.0 7.62 3.0 0.6 1.2 12.1 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 21 speci cations series name item fg, fgh type fgr type test conditions (conforming to jis c 5160-1) category temperature range 25 ? to 70 ? 40 ? to 85 ? max operating voltage 5.5vdc, 3.5vdc 5.5vdc capacitance fg0.010f to 4.7f fgh0.10f to 1.0f 0.47f to 2.2f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings refer to standard ratings measured at 1khz, 10ma ; see also lmeasurement conditions z current (30-minutes value) refer to standard ratings refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings more than 90% of initial ratings surge voltage 6.3v (5.5v type) 4.0v(3.5v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.010f 1500 0.022f 560 0.047f 300 0.10f 150 0.22f 56 0.47f 30 1.0f, 1.5f 15 2.2f, 4.7f 10 discharge resistance0 temperature 85?2 ? (fgr) 70?2 ? (fg, fgh) esr not to exceed 120% of initial ratings not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings not to exceed 120% of initial ratings appearance no obvious abnormality no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value phase 2 50% or higher than initial value conforms to 4.17 phase1 25?2 ? phase2 25?2 ? phase3 40?2 ? (fgr) phase4 25?2 ? phase5 70?2 ? (fg, fgh) 85?2 ? (fgr) phase6 25?2 ? esr 400% or less than initial value 400% or less than initial value capacitance phase 3 phase 3 30% or higher than initial value esr 700% or less than initial value capacitance phase 5 200% or less than initial value phase 5 200% or less than initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value phase 6 within ?20% of initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) satisfy initial ratings satisfy initial ratings lead strength (tensile) no terminal damage no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.13 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality temperature cycle capacitance satisfy initial ratings satisfy initial ratings conforms to 4.12 temperature condition category min temp room temp category max temproom temp number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality high temp. and high humidity resistance capacitance within ? 20% of initial value within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings not to exceed 120% of initial ratings appearance no obvious abnormality no obvious abnormality high temperature load capacitance within ? 30% of initial value within ?30% of initial value conforms to 4.15 temp category max temp ?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings below 200% of initial ratings current (30 minutes value) below 200% of initial ratings below 200% of initial ratings appearance no obvious abnormality no obvious abnormality self discharge characteristics (voltage holding characteristics) 5.5v type: voltage between terminal leads higher than 4.2v 3.5v type: not speci? ed voltage between terminal leads higher than 4.2v charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humiditylower than 70%rh all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 22 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. ymin. f d 2 ? 0.1 terminal a1 001 a1 ft ft 5.5 v 5.5 v 0.22 f 85? 85? 0.22 f super capacitor max operating voltage nominal capacitance date code serial number negative polarity identification mark markings on sleeve 6.4 f t series dimensions speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma dimension (unit:mm) weight g dh p d 1 d 2 y charge system (f) discharge system (f) ft0h104zf 5.5 0.10 0.14 16 0.15 11.5 8.5 5.08 0.4 1.2 2.7 1.6 ft0h224zf 5.5 0.22 0.28 10 0.33 14.5 12.0 5.08 0.4 1.2 2.2 4.1 ft0h474zf 5.5 0.47 0.60 6.5 0.71 16.5 13.0 5.08 0.4 1.2 2.7 5.3 ft0h105zf 5.5 1.0 1.3 3.5 1.5 21.5 13.0 7.62 0.6 1.2 3.0 10.0 ft0h225zf 5.5 2.2 2.8 1.8 3.3 28.5 14.0 10.16 0.6 1.4 6.1 18.0 ft0h335zf 5.5 3.3 4.2 1.0 5.0 36.5 15.0 15.00 0.6 1.7 6.1 38.0 ft0h565zf 5.5 5.6 7.2 0.6 8.4 44.5 17.0 20.00 1.0 1.4 6.1 72.0 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 23 speci cations series name item ft type test conditions (conforming to jis c 5160-1) category temperature range 40 ? to 85 ? max operating voltage 5.5vdc capacitance 0.1f to 5.6f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 6.3v charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.10f 150 0.22f 56 0.47f 30 1.0f 15 2.2f 10 3.3f 10 5.6f 10 discharge resistance0 temperature 85?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase340?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value capacitance phase 3 30% or higher than initial value esr 700% or less than initial value capacitance phase 5 200% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency 10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 40 ? room temperature 85 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance within ?30% of initial value conforms to 4.15 temperature 85?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 24 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. h ? 0.5 for fyl ymin. f d 2 ? 0.1 terminal a1 001 a1 fyd fyd 5.5 v 0.047 f 5.5 v 0.047 f negative polarity identification mark max operating voltage nominal capacitance date code serial number 6.5 fy series markings on sleeve dimensions /? fyd type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) FYD0H223ZF 5.5 0.022 0.033 220 0.033 4.2 11.5 8.5 5.08 2.7 0.4 1.2 1.6 fyd0h473zf 5.5 0.047 0.070 220 0.071 4.2 11.5 8.5 5.08 2.7 0.4 1.2 1.7 fyd0h104zf 5.5 0.10 0.14 100 0.15 4.2 13.0 8.5 5.08 2.2 0.4 1.2 2.4 fyd0h224zf 5.5 0.22 0.35 120 0.33 4.2 14.5 15.0 5.08 2.4 0.4 1.2 4.3 fyd0h474zf 5.5 0.47 0.75 65 0.71 4.2 16.5 15.0 5.08 2.7 0.4 1.2 6.0 fyd0h105zf 5.5 1.0 1.6 35 1.5 4.2 21.5 16.0 7.62 3.0 0.6 1.2 11.0 fyd0h145zf 5.5 1.4 2.1 45 2.1 4.2 21.5 19.0 7.62 3.0 0.6 1.2 12.0 fyd0h225zf 5.5 2.2 3.3 35 3.3 4.2 28.5 22.0 10.16 6.1 0.6 1.4 22.9 /? fyh type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fyh0h223zf 5.5 0.022 0.033 200 0.033 4.2 11.5 7.0 5.08 2.7 0.4 1.2 1.5 fyh0h473zf 5.5 0.047 0.075 100 0.071 4.2 13.0 7.0 5.08 2.2 0.4 1.2 2.2 fyh0h104zf 5.5 0.10 0.16 50 0.15 4.2 16.5 7.5 5.08 2.7 0.4 1.2 3.4 fyh0h224zf 5.5 0.22 0.30 60 0.33 4.2 16.5 9.5 5.08 2.7 0.4 1.2 3.6 fyh0h474zf 5.5 0.47 0.70 35 0.71 4.2 21.5 10.0 7.62 3.0 0.6 1.2 7.2 fyh0h105zf 5.5 1.0 1.5 20 1.5 4.2 28.5 11.0 10.16 6.1 0.6 1.4 13.9 /? fgl type speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fyl0h103zf 5.5 0.01 0.013 300 0.015 4.2 11.0 5.0 5.08 2.7 0.2 1.2 0.9 fyl0h223zf 5.5 0.022 0.028 200 0.033 4.2 11.0 5.0 5.08 2.7 0.2 1.2 1.0 fyl0h473zf 5.5 0.047 0.061 200 0.071 4.2 12.0 5.0 5.08 2.7 0.2 1.2 1.2 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 25 speci cations series name item fy type (fyd, fyh, fyl) test conditions (conforming to jis c 5160-1) category temperature range 25 ? to 70 ? max operating voltage 5.5vdc capacitance refer to standard ratings refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr fyd 0.022f to 2.2f fyh 0.022f to 1.0f fyl 0.010f to 0.047f measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 6.3v charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.010f 1500 0.022f 560 0.047f 300 0.068f 240 0.10f 150 0.22f 56 0.47f 30 1.0f, 1.4f 15 2.2f 10 discharge resistance0 temperature 70?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value conforms to 4.17 phase1 25 ?2 ? phase225?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value capacitance phase 3 esr capacitance phase 5 200% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time 10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 25 ? room temperature 70 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance within ?30% of initial value conforms to 4.15 temperature 70?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality self discharge characteristics (voltage holding characteristics) voltage between terminal leads higher than 4.2v charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humidity lower than 70%rh all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 26 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. ymin. f d 2 ? 0.1 terminal a1 001 a1 fr fr 5.5 v 85? 0.022 f 5.5 v 85? 0.022 f negative polarity identification mark max operating voltage nominal capacitance date code serial number 6.6 fr series markings on sleeve dimensions speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma voltage holding characteristics v dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fr0h223zf 5.5 0.022 0.028 220 0.033 4.2 11.5 14.0 5.08 2.7 0.4 1.2 2.3 fr0h473zf 5.5 0.047 0.060 110 0.071 4.2 14.5 14.0 5.08 2.4 0.4 1.2 3.9 fr0h104zf 5.5 0.10 0.15 150 0.15 4.2 14.5 15.5 5.08 2.4 0.4 1.2 4.3 fr0h224zf 5.5 0.22 0.33 180 0.33 4.2 14.5 21.0 5.08 2.4 0.4 1.2 5.3 fr0h474zf 5.5 0.47 0.75 100 0.71 4.2 16.5 21.5 5.08 2.7 0.4 1.2 7.5 fr0h105zf 5.5 1.0 1.6 60 1.5 4.2 21.5 22.0 7.62 3.0 0.6 1.2 13.3 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 27 speci cations series name item fr type test conditions (conforming to jis c 5160-1) category temperature range 40 ? to 85 ? max operating voltage 5.5vdc capacitance 0.022f to 1.0f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 6.3v (5.5v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.022f 560 0.047f 300 0.068f 240 0.10f 150 0.22f 56 0.47f 30 1.0f 15 discharge resistance0 temperature 70?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase340?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 400% or less than initial value capacitance phase 3 30% or higher than initial value esr 700% or less than initial value capacitance phase 5 200% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency 10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 40 ? room temperature 85 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance within ?30% of initial value conforms to 4.15 temperature 85?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality self discharge characteristics (voltage holding characteristics) voltage between terminal leads higher than 4.2v charging condition voltage applied 5.0vdc (terminal at the case's side be negative) series resistance0 charging time24 hours storage let stand for 24 hours in condition described below with terminals opened. ambient temperaturelower than 25 ? relative humidity lower than 70%rh all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 28 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. ymin. f d 2 ? 0.1 terminal a1 001 a1 fs fs 5.5 v 5.5 v 0.22 f 0.22 f negative polarity identification mark max operating voltage nominal capacitance date code serial number 6.7 fs series markings on sleeve dimensions speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fs0h223zf 5.5 0.022 0.033 60.0 0.033 11.5 8.5 5.08 2.7 0.4 1.2 1.6 fs0h473zf 5.5 0.047 0.072 40.0 0.071 13.0 8.5 5.08 2.2 0.4 1.2 2.6 fs0h104zf 5.5 0.10 0.15 25.0 0.15 16.5 8.5 5.08 2.7 0.4 1.2 4.1 fs0h224zf 5.5 0.22 0.33 25.0 0.33 16.5 13.0 5.08 2.7 0.4 1.2 5.3 fs0h474zf 5.5 0.47 0.75 13.0 0.71 21.5 13.0 7.62 3.0 0.6 1.2 10 fs0h105zf 5.5 1.0 1.3 7.0 1.5 28.5 14.0 10.16 6.1 0.6 1.4 18 fs1a474zf 11.0 0.47 0.60 7.0 1.41 28.5 25.5 10.16 6.1 0.6 1.4 32 fs1a105zf 11.0 1.0 1.3 7.0 3.0 28.5 31.5 10.16 6.1 0.6 1.4 35 fs1b105zf 12.0 1.0 1.3 7.5 3.6 28.5 38.0 10.16 6.1 0.6 1.4 40 fs1b505zf 12.0 5.0 6.5 4.0 18.0 44.8 60.0 20.00 9.5 1.0 1.4 160 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 29 speci cations series name item fs type test conditions (conforming to jis c 5160-1) category temperature range 25 ? to 70 ? max operating voltage 5.5vdc, 11vdc, 12vdc capacitance 5.5v0.022f to 1.0f 11v 0.47, 1.0 12v 1.0f, 5.0f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? refer to lmeasurement conditions z esr 5.5v0.0022f to 1.0f 11v 0.47f, 1.0f 12v 1.0f, 5.0f measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 6.3v (5.5v type) 12.6v (11v type) 13.6v (12v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.022f 560 0.047f 300 0.10f 150 0.22f 56 0.47f 30 1.0f 15 5.0f 10 discharge resistance0 t emperature70?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 50% or higher than initial value conforms to 4.17 phase125?2 ? phase225?2 ? phase425?2 ? phase570?2 ? phase625?2 ? esr 300% or less than initial value capacitance phase 3 esr capacitance phase 5 150% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings conforms to 4.13 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.12 temperature condition 25 ? room temperature 70 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance over 90% of the initial value (5.5v type) within ? 20% of initial value (11v type, 12vtype) conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance over 85% of the initial value (5.5v type) within ? 20% of initial value (11v type, 12vtype) conforms to 4.15 temperature 70?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 30 super capacitors vol.12 d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 2.0 max. h max. ymax. f d 2 ? 0.1 terminal a1 001 a1 001 fa fa fa fa 5 v 0.1 f 5 v 0.1 f 5 v 0.1 f 5 v 0.1 f negative polarity identification mark rated voltage nominal capacitance date code serial number d 1 ? 0.1 p ? 0.5 sleeve d ? 0.5 0.3 min. h max. ymin. f d 2 ? 0.1 terminal a1 001 a1 fe fe 5.5 v 0.047 f 5.5 v 0.047 f negative polarity identification mark max operating voltage nominal capacitance date code serial number 6.8 fa series, fe series /? fa series dimensions /?fe series dimensions markings on sleeve markings on sleeve speci cations part number max operating voltage vdc rated voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fa0h473zf 5.5 5 0.047 0.075 20.0 0.071 16.0 15.5 5.1 5.0 0.4 1.2 6.2 fa0h104zf 5.5 5 0.10 0.16 8.0 0.15 21.5 15.5 7.6 5.5 0.6 1.2 12 fa0h224zf 5.5 5 0.22 0.35 5.0 0.33 28.5 16.5 10.2 9.5 0.6 1.4 25 fa0h474zf 5.5 5 0.47 0.75 3.5 0.71 36.5 16.5 15.0 9.5 0.6 1.7 42 fa0h105zf 5.5 5 1.0 1.6 2.5 1.5 44.5 18.5 20.0 9.5 1.0 1.4 65 fa1a223zf 11.0 10 0.022 0.035 20.0 0.066 16.0 25.0 5.1 5.0 0.4 1.2 7.5 fa1a104zf 11.0 10 0.10 0.16 8.0 0.30 28.5 25.5 10.2 9.5 0.6 1.4 32 fa1a224zf 11.0 10 0.22 0.35 6.0 0.66 36.5 27.5 15.0 9.5 1.0 1.4 55 fa1a474zf 11.0 10 0.47 0.75 4.0 1.41 44.5 28.5 20.0 9.5 1.0 1.4 83 speci cations part number max operating voltage vdc nominal capacitance max esr at 1 khz $? max current at 30 min. ma dimension (unit:mm) weight g dh p y d 1 d 2 charge system (f) discharge system (f) fe0h473zf 5.5 0.047 0.075 14.0 0.071 14.5 14.0 5.1 2.2 0.4 1.2 3.9 fe0h104zf 5.5 0.10 0.16 6.5 0.15 16.5 14.0 5.1 2.7 0.4 1.2 5 fe0h224zf 5.5 0.22 0.35 3.5 0.33 21.5 15.5 7.6 3.0 0.6 1.2 9.5 fe0h474zf 5.5 0.47 0.75 1.8 0.71 28.5 16.5 10.2 6.1 0.6 1.4 16 fe0h105zf 5.5 1.0 1.4 1.0 1.5 36.5 18.5 15.0 6.1 0.6 1.7 38 fe0h155zf 5.5 1.5 2.1 0.6 2.3 44.5 18.5 20.0 6.1 1.0 1.4 72 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 31 speci cations series name item fa fe test conditions (conforming to jis c 5160-1) category temperature range 25 ? to 70 ? 40 ? to 70 ? max operating voltage 5.5vdc, 11vdc 5.5vdc capacitance 5.5v0.047f to 1.0f 11v 0.022f to 0.47f 0.047f to 1.5f refer to lmeasurement conditions z capacitance allowance 80 ?, 20 ? 80 ?, 20 ? refer to lmeasurement conditions z esr refer to standard ratings refer to standard ratings measured at 1khz, 10ma ; see also lmeasurement conditions z current (30-minutes value) refer to standard ratings refer to standard ratings refer to lmeasurement conditions z surge capacitance more than 90% of initial ratings surge voltage 6.3v (5.5v type) 12.6v (11v type) charge30 sec. discharge9min 30sec. number of cycles1000 series resistance 0.047f 300 0.10f 150 0.22f 56 0.47f 30 1.0f, 1.5f 15 discharge resistance0 temperature 70?2 ? esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality characteristics in different temperature capacitance phase 2 70% or higher than initial value phase 2 conforms to 4.17 phase125?2 ? phase225?2 ? phase340?2 ? (fe type) phase425?2 ? phase570?2 ? phase625?2 ? esr 300% or less than initial value capacitance phase 3 phase 3 40% or higher than initial value esr 400% or less than initial value capacitance phase 5 150% or less than initial value phase 5 200% or less than initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) 1.5cv (ma) or below 1.5cv (ma) or below capacitance phase 6 within ?20% of initial value phase 6 within ?20% of initial value esr satisfy initial ratings satisfy initial ratings current (30 minutes value) satisfy initial ratings satisfy initial ratings lead strength (tensile) no terminal damage no terminal damage conforms to 4.9 vibration resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.13 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder over 3/4 of the terminal should be covered by the new solder conforms to 4.11 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings satisfy initial ratings conforms to 4.10 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality temperature cycle capacitance satisfy initial ratings satisfy initial ratings conforms to 4.12 temperature condition 25 ? (40 ? for fe type) room temperature 70 ? room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality no obvious abnormality high temp. and high humidity resistance capacitance over 90% of initial value within ?20% of initial value conforms to 4.14 temperature 40?2 ? relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings not to exceed 120% of initial ratings appearance no obvious abnormality no obvious abnormality high temperature load capacitance over 85% of initial value within ?30% of initial value conforms to 4.15 temperature 70?2 ? voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 120% of initial ratings below 200% of initial ratings current (30 minutes value) below 200% of initial ratings below 200% of initial ratings appearance no obvious abnormality no obvious abnormality all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 32 super capacitors vol.12 negative terminal p ? 0.1 ?d ? 0.5 ?d positive terminal ? l min. l min. h 2.7v 10f supercapacitor hv 6.9 hv series (high capacitance type) dimensions markings on sleeve speci cations part number max operating voltage vdc nominal capacitance f max esr at 1 khz $? max current at 30 min. ma dimension (unit:mm) weight g dh p dl ? l hvs0e106nf 2.7 10 100 8 10.0 35 ? 2 5.0 0.6 15.0 5.0 4.5 hvs0e226nf 2.7 22 100 18 12.5 35 ? 2 5.0 0.6 15.0 5.0 6.5 hvs0e506nf 2.7 50 30 40 18.0 40 ? 5 7.5 0.8 15.0 5.0 14.0 hvs0e107nf 2.7 100 30 81 22.0 50 ? 5 10.2 1.0 15.0 5.0 24.0 speci cations item speci? cations test conditions (conforming to jis c 5160-2) category temperature range 25 ? to 60 ? (50f, 100f), 25 ? to 70 ? (10f, 22f), max operating voltage 2.7vdc capacitance 10f, 22f, 50f, 100f refer to lmeasurement conditions z capacitance allowance ?30 ? refer to lmeasurement conditions z esr refer to standard ratings measured at 1khz, 10ma ; see also l measurement conditions z current (30-minutes value) refer to standard ratings refer to lmeasurement conditions z characteristics in different temperature capacitance phase 2 50% higher than initial value conforms to 4.13 phase2category min temp. phase4category max temp. phase525 ? esr 400% or less than initial value capacitance phase 4 150% or less than initial value esr satisfy initial ratings current (30 minutes value) 1.510 3 cv (a) or below capacitance phase 5 within ?20% of initial value esr satisfy initial ratings current (30 minutes value) satisfy initial ratings lead strength (tensile) no terminal damage conforms to 4.5 vibration resistance capacitance satisfy initial ratings conforms to 4.9 frequency10 to 55 hz testing time 6 hours esr current (30 minutes value) appearance no obvious abnormality solderability over 3/4 of the terminal should be covered by the new solder conforms to 4.7 solder temp245?5 ? dipping time5?0.5 sec. 1.6mm from the bottom should be dipped. solder heat resistance capacitance satisfy initial ratings conforms to 4.6 solder temp260?10 ? dipping time10?1 sec. 1.6mm from the bottom should be dipped. esr current (30 minutes value) appearance no obvious abnormality temperature cycle capacitance satisfy initial ratings conforms to 4.8 temperature condition 25 ? room temperature 70 ? (10f, 22f), 60 ? (50f, 100f) room temperature number of cycles5 cycles esr current (30 minutes value) appearance no obvious abnormality high temp. and high humidity resistance capacitance within ?20% of initial value conforms to 4.14 temperature 40?2 ? (50f, 100f) relative humidity90 to 95 ?rh testing time 240?8 hours esr not to exceed 120% of initial ratings current (30 minutes value) not to exceed 120% of initial ratings appearance no obvious abnormality high temperature load capacitance within ?30% of initial value conforms to 4.10 temperature 70 ? (10f, 22f), 60 ? (50f, 100f) voltage applied max operating voltage series protection resistance0 testing time 1000 48 y0 hours esr below 200% of initial ratings current (30 minutes value) below 200% of initial ratings appearance no obvious abnormality all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 33 7. packing 1. fm series (1) bulk /packing method pack in vinyl bags then pack them into cardboard boxes. /standard packing quantity 1000pcs (100pcs / vinyl bag10) howeverfm0h104zf-l1 and fm0h224zf-l11800pcs, fmc0h334zf1400pcs, fmc0h334zf-l11300pcs (2) taping /packing method ammo pack /standard packing quantity 1000pcs however, fmc0h334zftp( ) = 400pcs 2. fc series part name packing unit fc0h473zftbr24 1000 pcs. / reel fc0h104zftbr24 1000 pcs. / reel fc0h224zftbr24 500 pcs. / reel fc0h474zftbr32-ss 200 pcs. / reel fc0h105zftbr44-ss 150 pcs. / reel fc0v104zftbr24 1000 pcs. / reel fc0v224zftbr24 1000 pcs. / reel fc0v474zftbr24 500 pcs. / reel fcs0h473zftbr24 1000 pcs. / reel fcs0h104zftbr24 1000 pcs. / reel fcs0h224zftbr24 500 pcs. / reel fcs0v104zftbr24 1000 pcs. / reel fcs0v224zftbr24 1000 pcs. / reel fcs0v474zftbr24 500 pcs. / reel fch0v683zftbr16 1500 pcs. / reel fch0h433zftbr16 1500 pcs. / reel 3} fg, ft, fs, fr, fy, fa series (1) bulk (small type) /packing method pack in vinyl bags then pack them into cardboard boxes. / standard packing quantity: see chart below. unitpises series name capacitance fa fe fs fy fr fg ft 5.5v type 11v type 5.5v type 11v type, 12v type fyd fyh fyl 0.010f 2000 2000 0.022f 240 1000 1000 1600 2000 800 2000 0.047f 400 400 800 1000 800 1600 400 2000 0.10f 400 600 800 600 400 1600 1000 0.22f 400 400 500 300 800 400 0.47f 240 240 300 400 1.0f 240 (2) bulk (large type) /packing method: pin the terminal onto a conductive mat; then pack it into individual cardboard box with insulation material. / standard packing quantity: see chart below. unitpises series name capacitance fa fe fs fy fr fg ft 5.5v type 11v type 5.5v type 11v type, 12v type fyd fyh fyl 0.10f 90 50 0.22f 50 30 90 0.47f 30 20 50 90 50 90 1.0f 20 30 50 50 90 50 90 90 1.4f 90 1.5f 20 160 2.2f 50 90 50 3.3f 30 4.7f 50 5.0f 20 5.6f 20 4. winded type (hv series) /packing method pack in vinyl bags then pack them into cardboard boxes. /standard packing quantity 320pcs (10f), 224pcs (22f), 120pcs (50f), 80pcs (100f) all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 34 super capacitors vol.12 by changing the solder plating from leaded solder to lead-free solder, and the outer tube material of can-cased conventional supercapacitor from polyvinyl chloride to polyethylene terephathatate (pet), our new supercapacitor has now became even more friendlier to the environment. a. iron copper base lead-free solder plating (sn-1cu) b. sus nickel base copper base re? ow lead-free solder plating (100% sn, re? ow processed) c. iron copper base lead-free solder plating (100% sn) series part number plating sleeve fa all fa series a pet (blue) fe all fe series a pet (blue) fs all fs series a pet (blue) fr all fr series a pet (blue) ft all ft series a pet (blue) fy all fyd type a pet (blue) all fyh type a pet (blue) fyl0h473zf a pet (blue) fyl0h223zf b pet (blue) fyl0h103zf b pet (blue) fg fg0h103zf b petblue fg0h223zf b petblue fg0h473zf b petblue fg0h104zf b petblue fg0h224zf a petblue fg0h474zf a petblue fg0h105zf a petblue fg0h225zf a petblue fg0h475zf a petblue fgh0h104zf b petblue fgh0h224zf b petblue fgh0h474zf a petblue fgh0h105zf a petblue all fgr type a petblue fm all fm series a no tube used fc fc0h473zftbr24 b no tube used fc0h104zftbr24 b no tube used fc0h224zftbr24 b no tube used fc0h474zftbr32-ss a no tube used fc0h105zftbr44-ss a no tube used fc0v104zftbr24 b no tube used fc0v224zftbr24 b no tube used fc0v474zftbr24 b no tube used fch0v683zftbr16 b no tube used fch0h433zftbr16 b no tube used fcs0h473zftbr24 b no tube used fcs0h104zftbr24 b no tube used fcs0h224zftbr24 b no tube used fcs0v104zftbr24 b no tube used fcs0v224zftbr24 b no tube used fcs0v474zftbr24 b no tube used hv all hv series c pet (blue) recommended pb-free solder : sn / 3.5ag / 0.75cu sn / 3.0ag / 0.5cu sn / 0.7cu sn / 2.5ag / 1.0bi / 0.5cu 8. list of plating type and sleeve type all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 35 9. measurement conditions v c r c e o swich c + ? e o : 3.0 (v) ? product with maximum operating voltage 3.5 v 5.0 (v) ? product with maximum operating voltage 5.5 v 6.0 (v) ? product with maximum operating voltage 6.5 v 10.0 (v) ? product with maximum operating voltage 11 v 12.0 (v) ? product with maximum operating voltage 12 v : time from start of charging until vc becomes 0.632e 0 (v) (sec) r c : see table below ( $?). capacitance: c = (f) (9) r c capacitance (discharge system) in the diagram below, charging is performed for a duration of 30 minutes, once the voltage of the condensor terminal reaches 5.5 v. then, use a constant current load device and measure the time for the terminal voltage to drop from 3.0 to 2.5 v upon discharge at 0.22 ma for 0.22 f, for example, and calculate the static capacitance according to the equation shown below. note: the current value is 1 ma discharged per 1f. a v cr 5.5v sw 0.22ma(i) 30 min. t1 t2 v 1 : 2.5v v 1 : 3.0v 5.5v v 1 v 2 voltage duration (sec.) table 3 capacitance measurement capactancec1 (f) i(t 2 t 1 ) v 1 v 2 (1) capacitance ( charge system ) capacitance is calculated from expression (9) by measuring the charge time constant ( ) of the capacitor (c). prior to measurement, short between both pins of the capacitor for 30 minutes or more to let it discharge. in addition, follow the indication of the product when determining the polarity of the capacitor during charging. fa fe fs fy fr fm, fme fmr, fml fmc fg fgr fgh ft fc, fch fcs fyd fyh fyl 0.010f ? ? ? ? ? 5000 $? ? 5000 $? ? 5000 $? ??? 0.022f 1000 $? ? 1000 $? 2000 $? 2000 $? 2000 $? 2000 $? 2000 $? ? 2000 $? ?? discharge 0.033f ? ? ? ???? discharge ????? 0.043f ? ? ? ???? ? ???? discharge 0.047f 1000 $? 1000 $? 1000 $? 2000 $? 1000 $? 2000 $? 1000 $? 2000 $? 1000 $? 2000 $? ??? 0.068f ? ? ? ???? ? ???? discharge 0.10f 510 $? 510 $? 510 $? 1000 $? 510 $? ? 1000 $? 1000 $? 1000 $? 1000 $? discharge 510 $? discharge 0.22f 200 $? 200 $? 200 $? 510 $? 510 $? ? 510 $? 0h: discharge 0v: 1000 $? ? 1000 $? discharge 200 $? discharge 0.33f ? ? ? ???? ? discharge ???? 0.47f 100 $? 100 $? 100 $? 200 $? 200 $? ? 200 $? ? ? 1000 $? discharge 100 $? discharge 1.0f 51 $? 51 $? 100 $? 100 $? 100 $? ? 100 $? ? ? 510 $? discharge 100 $? discharge 1.4f ? ? ? 200 $? ??? ? ????? 1.5f ? 51 $? ????? ? ? 510 $? ??? 2.2f ? ? ? 100 $? ? ? ? ? ? 200 $? ? 51 $? ? 3.3f ? ? ? ???? ? ???51 $? ? 4.7f ? ? ? ???? ? ? 100 $? ??? 5.0f ? ? 100 $? ???? ? ????? 5.6f ? ? ? ???? ? ??? 20 $? ? *capacitance values according to the constant current discharge method. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 36 super capacitors vol.12 10. notes on using super capacitor (electric double-layer capacitor) 1. circuitry design 1.1 useful life the electrical double layered capacitor (super capacitor) uses electrolyte and is sealed with rubber etc. water in the electrolyte can evaporate in use over long periods at high temperatures, thus reducing electrostatic capacity which in turn wil l create greater internal resistance. the characteristics of the super capacitor can vary greatly depending on the environment it is used in. therefore, controlling the usage environment will ensure prolonged life of the part. basic breakdown mode is an open mode due to increased internal resistance. 1.2 fail rate in the ? eld based on ? eld data, the fail rate is calculated at approx. 0.006fit. we estimate that unreported failures are ten times this amount. therefore, we assume that the fail rate is below 0.06fit. 1.3 voltage application when maximum usable voltage is exceeded performance may be compromised, and in some cases leakage or damage may occur if applied voltage exceeds maximum working voltage. 1.4 use of capacitor as a smoothing capacitor (ripple absorption) in electrical circuits as super capacitors contain a high level of internal resistance, they are not recommended for use as electrical smoothing capacitors in electrical circuits. performance may be compromised, and in some cases leakage or damage may occur if a super capacitor is used in ripple absorption. 1.5 series connections as applied voltage balance to each super capacitor is lost when used in series connection, excess voltage may be applied to some super capacitors, which will not only negatively affect its performance but may also cause leakage and/or damage. allow ample margin for maximum voltage or attach a circuit for applying equal voltage to each super capacitor (partial pressure resistor/voltage divider) when using super capacitors in series connection. also, arrange super capacitors so that the temperature between each capacitor will not vary. 1.6 outer sleeve insulation the outer sleeve wrapped around the super capacitor indicates that it is sealed, however the outer sleeve is not guaranteed for insulation purposes. therefore, it cannot be used where insulation is necessary. 1.7 polar characteristics the super capacitor is manufactured so that the terminal on the outer case is negative (-). align the (-) symbol during use. even though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts. 1.8 use next to heat emitters useful life of the super capacitor will be signi? cantly affected if used near heat emitting items (coils, power transistors, a nd posistors etc) where the super capacitor itself may become heated. 1.9 usage environment this device cannot be used in any acidic, alkaline or similar type of environment. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e super capacitors vol.12 37 1.10 super capacitors ? tted with pressure valves hv series super capacitors are ? tted with pressure valves make an opening in the top of the pressure valve to avoid any damage to the super capacitor when the pressure valve is in use. allow at least a 2mm opening for models with a diameter of 18mm or less, and at least a 3mm opening for models with a diameter of 22mm. 2. mounting 2.1 mounting onto a re? ow furnace except for the fc series, it is not possible to mount this capacitor onto an ir / vps re? ow furnace. do not immerse the capacitor into a soldering dip tank. 2.2 flow soldering conditions keep solder under 260 ? and soldering time to within 10 seconds when using the ? ow automatic soldering method. (except for the fc and hv series) 2.3 installation using a soldering iron care must be taken to prevent the soldering iron from touching other parts when soldering. keep the tip of the soldering iron under 400 ? and soldering time to within 3 seconds. always make sure that the temperature of the tip is controlled. internal capacitor resistance is likely to increase if the terminals are overheated. 2.4 lead terminal processing do not attempt to bend or polish the capacitor terminals with sand paper etc. soldering may not be possible if the metallic plating is removed from the top of the terminals. 2.5 cleaning, coating, and potting except for the fm series, cleaning, coating, and potting must not be carried out. consult us if this type of procedure is necessary. terminals should be dried at less than the maximum operating temperature after cleaning. 3. storage 3.1 temperature and humidity make sure that the super capacitor is stored according to the following conditions: temp.: 5 ?35 ? (standard 25), humidity: 20?70% (standard: 50%). do not allow the build up of condensation through sudden temperature change. 3.2 environment conditions make sure that there are no corrosive gasses like sulfur dioxide as penetration of the lead terminals is possible. always store this item in an area with low dust and dirt levels. make sure that the packaging will not be deformed through heavy loading, movement and/or knocks. keep out of direct sunlight, and away from radiation, static electricity, and magnetic ? elds. 3.3 maximum storage period this item may be stored up to one year from the date of delivery if stored at the conditions stated above. this product should be safe to use even after being stored for over a 1 year period. however, depending on the storage conditions, we recommend that the soldering is checked. 4. dismantling there is a small amount of electrolyte stored within thecapacitor. do not attempt to dismantle as direct skin contact with the electrolyte will cause burning. this product should be treated as industrial waste and not is not to be disposed of by ? re. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e 38 super capacitors vol.12 all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e when using our products, the following precautions should be taken. (1) safety designing of an apparatus or a system allowing for failures of electronic components used in the system in general, failures will occur in electronic components at a certain probability. nec tokin makes every effort to improve the quality and reliability of electronic component products. however, it is impossible to completely eliminate the probability of failures. therefore, when using nec tokin? electronic component products, systems should be carefully designed to ensure redundancy in the event of an accident which would result in injury or death, fire, or social damage, to ensure the prevention of the spread of fire, and the prevention of faulty operation. (please refer to pre-cautions to be taken when using supercapacitor capacitors for the details of failures.) (2) quality level of various kinds of parts, and equipment in which the parts can be utilized electronic components have a standard quality level unless otherwise specified. nec tokin classifies the level of quality of electronic component products into three levels, in order from a lower level, a standard quality level, a special quality level, and a custom quality level in which a customer individually specifies a quality assurance program. each of the quality levels has recommended applications. if a user wants to use the electronic parts having a standard quality level in applications other than the applications specified for the standard quality level, they should always consult a member of our company? sales staff before using the electronic parts. standard quality level: computers, office automation equipment, communications equipment, measuring instruments, av equipment, household electrical appli- ances, machine tools, personal equipment, industrial robots special quality level: transportation equipment (automobiles, railways, shipping, or the like), traffic signals, disaster prevention/crime prevention systems, safety devices, and medical equipment which is not directly intended for life-support purposes custom quality level: equipment for airplanes, aerospace equipment, nuclear power control systems, and medical equipment, apparatus or systems for life-sup- port purposes unless otherwise shown, the quality level of nec tokin? electronic component products included in documents such as catalogues, data sheets or data books is the standard quality level. (3) this manual is subject to change without notice. the contents of this manual are based on data which is correct as of july 2010, and they may be changed without notice. if our products are used for mass-production design, please cousult with a member of our company? sales staff by way of precaution. (4) reprinting and copying of this manual without prior written permission from nec tokin corpo- ration are not permitted. (5) industrial property problems in the event any problems associated with industrial property of a third party arising as a result of the use of our products, nec tokin assumes no responsibility for problems other than problems directly associated with the constitution and manufacturing method of the products. (6) should any of these products come under the category of strategic goods or services (according to japan's foreign trade and foreign exchange regulations), the sender must obtain an export license from the japanese government befor said products can be exported outside japan. all specifcations in this catalog and production status of products are subject to change without notice. prior to the purchase, please contact nec tokin for updated product data. please request for a specifcation sheet for detailed product data prior to the purchase. before using the product in this catalog, please read "precautions" and other safety precautions listed in the printed version catalog. 2010.11.8 9565scavol12e |
Price & Availability of FYD0H223ZF
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |